home-insulation_20100121144137






The attic of your house should be properly insulated as almost half of the total heat loss of your house leaks through the attic. Attic insulation has never been more important for now with the escalating cost of non-renewable energy such as petroleum.

When the attic of your house is not properly insulated, the amount of heat loss through the attic will be significant which can cause the heating bills to climb through the roof. With that being said, when it comes to finding ways to keep your heating and cooling costs down, there is nothing better than installing attic insulation.

Although attic ventilation is an important aspect for your house, the insulation part is an even more important issue to address and you might want to make sure that the insulation in the attic is properly done or else you will see your heating bills climb at a crazy rate.

With a properly installed attic insulation, the amount of saving in terms of heating and cooling cost will be significant and the saving from lower energy usage really helps especially at a time when the cost of everything is on the rise and the economy looks gloomy.

While the installation of an attic ventilation system is an easy task and take you only about a day, it might not be true for attic insulation installation and it depends largely on the set up of your attic.

There are a couple of options when it comes to insulating the attic. But the most commonly done practices can be narrowed down to only two ways. One way is to tear down all of the drywalls or plasters for a finished attic before installing the insulation. After the insulation is properly done, you can put the walls back.

The other way is to cut small holes on the walls without tearing them down. With the holes cut, you apply the insulation such as loose-fill cellulose, fiberglass, wool and rock by blowing them in through the walls. For more information on blown in insulation, you can read about it in this article here, Attic Blown In Insulation. When the insulation is done, you just simply repair the holes in the wall. Apparently this is a better and less expensive way that requires less work to insulate your attic.

Either way can be done and each has its pros and cons in terms of cost and the time involved. Before you decide on which way to go for attic insulation, you simply inspect the attic to figure out the types the attic belongs to, crawl or full. For more information on the crawl and full attic, you can read more about it in this article, Attic Insulation Inspection.

For example, for a full attic which can be turned into an active room where a person can easily walk around, you may want to consider tearing down all the drywalls and plasters and install new ones once the attic insulation is up. This method of attic insulation probably cost more but you gain more in the long run since you have transformed the attic into an extra room.

If you are on a limited budget but you know how to put up the drywalls, it makes more financial sense by going the route of ripping out and replacing walls. The downside for doing this on your own is you will be spending more time on this project. If you don’t know how to put up the drywalls, then you definitely want to hire a contractor to do this for you. You need to be aware that it can be expensive by hiring a contractor. Therefore, the advice here is do some work upfront such as estimate the cost first by getting free quote from respective contractors to see if the total cost of the project falls within your budget.

The other way of installing attic insulation by cutting holes is more economical for a crawl attic where the roof is close to the floor. You can simply cut holes on the walls and blown the insulation in without tearing the walls down. You will save an incredible amount of money by installing the insulation on your own if you are able to rent the machine to blow the attic insulation in yourself. But if you are looking at having to hire contractors to come out to do it then you will be looking at an expensive project which may not fit into your budget.

Lastly, no matter which way you go for attic insulation, you need to make sure that the attic insulation is not left exposed. During the installation period, tiny pieces of the insulation material can get into the air even with an attic ventilation system in place. These tiny particles can cause major health problems if you and your family members breathe them in. If you have to take a break between installing the insulation and the drywall make sure that you are at least covering the walls with thick and heavy plastic.

Related Home Insulation Guide